Aussie Bonza 3 Elite Instrukcja Użytkownika

Aussie®by Meco®LP Gas GrillAssembly and Use ManualFor Customer Service, call 1-800-251-7558 or visit our web site at www.aussiegrill.comFOR OUTDOOR HO

Step 9) Install Cooking Grids:Place Cooking Grids onto the front and back Bowl ridges over the Flame Diffusers and MainBurners. (FIG. 9)10Step 8) Inst

11To reduce the risk of serious bodily injury or death:· Use only propane gas in this LP gas grill. · Do not attempt to convert an LP unit to natural

4) Turn the adjusting knob clockwise to secure LP cylinder inside support bracket. (FIG. 13A)12FIG. 10AFIG. 10B5) Remove the protective cap from the L

13How to perform a leak test:Supplies Needed for a Leak Test: Clean paint brush, waterand dish washing liquid.1) Use an LP Cylinder equipped with an O

146. If any of the burners fail to light,repeat Step 4. The burnershould light within three or four attempts. If any or allburners fail to light aft

15CHECK YOUR FLAMEYellow TipPrimarily BlueFlameYour burners have been preset by the manufacturer for opti-mal flame performance. A blue flame, possibl

16· If you notice grease or other hot material dripping from the grill onto the valve, hose, or regulator, turn off the gas supply immediately. After

Spiders or small insects can build nests, webs and lay eggsin the grills venturi tubes obstructing the flow of gas to theburner. The backed-up gas can

18Lift up and slideBurner back.FIG. 15D9) Lift Burner up from the back and pull it towards the rear. In order to clear the warming rack, lean the burn

19STORAGETo reduce the risk of serious bodily injury or death:· Store your LP gas grill in a cool dry place. Do not store an LP gas cylinder in a spac

2I. Assembly Instructions...2Parts Illustrations...

Problem:Possible Cause:Solution:Burner will not light using the IgniterBurner is not connected toValve.Not pausing long enoughbefore clicking the Igni

Gas in LP Cylinder is lowExcess flow valve tripped inregulatorCheck LP gas cylinder. Refill if necessary.Turn control knobs to “off” position and turn

SERVICE PARTSHOOD ASSEMBLYTEMPERATURE GUAGEHANDLEHINGECONTROL KNOBCOOKING GRIDFLAME DIFFUSERBURNERCROSSOVER22BODY ASSEMBLYIGNITERGREASE PANBOTTOM PANE

SERVICE PARTS23

IMPORTANT NOTICEThe Gas Grill is setup to operate with a LP Gas Cylinder equippedwith an OPD (Overfill Prevention Device).This is a secondary device

MECO CORPORATIONLIMITED WARRANTYThis product is warranted to the original consumer purchaser against defects in material and workman-ship under normal

3STEP 1) Legs/Side Table Assembly:Attach the Wheel and Caster Legs to the Side Tables with 1/4-20 x 1-3/8” Bolts through the legsinto threaded insert

4(9) Bottom Shelf1 pc(8) Bolt, 1/4-20 x 1/2”2 pcSTEP 2) Install LP Cylinder Storage Guard:Place the LP Cylinder Wire Guard at an angle through the fir

5Step 3) Assemble Bottom Shelf to Legs:• Place the Leg/Side Table/LegAssemblies opposite each other with the velcro patches on same side. (FIG. 3)• Pl

6(13) Axle1 pc(14) WheelAssembly2 pc(11) Caster Wheel2 pcStep 4) Assemble Wheels, Casters, and LP Cylinder Support:• Thread Caster Wheels into the Rig

7(16) Bottom Body Panel1 pc(15) Grill Body1 pc(18) Spacer8 pc(19) Wingnut, M68 pcStep 5) Assemble Grill Body to Cart:• Remove the Bottom panel from t

8Step 6) Install Control Knobs, Fabric Panel, and Hood Handle:• Align the flat keyed hole in the Control Knobs with the keyed stem of the Control valv

9Step 7) Install Bottom Panel and Grease Tray:Slide the Bottom Panel into the track at the bottom of the grill body. (FIG. 7A) Secure BottomPanel int